Wireless Kit for Touch Board Plus
Connecting the Touch Board Plus
When the two devices have been successfully paired, the blue light on the RFCOM will stop blinking and remain a solid blue. The light will dim when connection to the MultiHub is lost.
Turning Technologies Device Manager version 7.3 or higher must be installed on your computer prior to installing the Wireless Kit.
Device Manager is automatically installed with the following software: WorkSpace (v.9.4) and Flow (v.2.0).The MultiHub plugs into a USB port on your computer or a powered USB Hub. The RFCOM (Radio Frequency Communicator) plugs into a wall outlet while positioned in the RFCOM clip that slips over the frame at the side of the Touch Board.
Connecting the Touch Board Plus
Turning Technologies Device Manager version 7.3 or higher must be installed on your computer prior to installing the Wireless Kit.
The MultiHub plugs into a USB port on your computer or a powered USB Hub. The RFCOM (Radio Frequency Communicator) plugs into a wall outlet while positioned in the RFCOM clip that slips over the frame at the side of the Touch Board Plus.Pairing the device is a one-time operation.
- Slide the plastic gray clip over the frame at the side of the Touch Board Plus.
- Seat the RFCOM
into the plastic gray clip.
- Connect the appropriate end of the power cord
into the power cord terminal and the opposite end into a nearby wall outlet.
- Connect the USB cable from the Touch Board Plus to the RFCOM
.
- Turn on the RFCOM power switch
. The amber light will turn on to show a successful connection to the Touch Board Plus.
- Plug the MultiHub into a working USB port on your computer or a powered USB hub.
- Press the pairing button on the MultiHub. The blue light will begin to blink.
- Press the pairing button
on the RFCOM.
IMPORTANT
You have two minutes to press the pairing button.
When the two devices have been successfully paired, the blue light on the RFCOM will stop blinking and remain a solid blue. The light will dim when connection to the MultiHub is lost.
Regulatory Statements Declaration of Conformity
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
European Union Emission Directive
This product is in conformity with the protection requirements of EU Council Directive 89/366/ECC on the approximation of the laws of the Member States relating to electromagnetic compatibility.This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to CISPR 22/European Standard EN55022. The limits for Class A equipment were derived for typical industrial environments to provide reasonable protection against interference with licensed communication devices.
European Union WEEE Directive
This product is in conformity with the protection requirements of EU Council Directive 89/366/ECC on the approximation of the laws of the Member States relating to electromagnetic compatibility.This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to CISPR 22/European Standard EN55022. The limits for Class A equipment were derived for typical industrial environments to provide reasonable protection against interference with licensed communication devices.
Manufacturer's Name:
Turning Technologies, LLC/DBA eInstructionManufacturer's HQ Address:
255 West Federal Street, Youngstown, Ohio 44503 U.S.A.European Address:
26/36 rue Alfred Nobel, 93600 Aulnay Sous Bois, FrancePhone:
+33 1 58 31 10 60 Fax: +33 1 58 31 10 69declares, that the product Product Names:
Wireless Kit for Touch BoardRegulatory Model #:
TBRF-01 USB RF Hub= H4 RFCOM= B4FCC ID:
CTW-MOBIIC:
4524A-MOBI
Conforms to the following specifications:
EMC: EN 301 489-1, EN 301 489-17 & ETSI/EN 301 489-3.EN 300-328 V1.7.1, EN55022:2006 and A1:2007 EN55024:1998+A1;2001+A2:2003
EN 61000-3-2:2006 ; EN 61000-3-3:2008
EN 61000-4-2:2009 ; EN 61000-4-3:2006 EN 61000-4-4:2004+A1:2010
EN 61000-4-5:2006; EN 61000-4-6:2009
EN 61000-4-11:2004; FCC Part 15B Class A Digital Device RSS-210
CE Marking:This product carries the
RoHS:“-R” labeled products conform to Directive 2011/65/EU (Directive 2002/95/EC). These products are RoHS-compliant.
Ohio
255 West Federal Street Youngstown, Ohio 44503Toll-Free: 866.746.3015
International: +1.330.746.3015
Arizona
7400 East Tierra Buena Lane, Suite 103Scottsdale, Arizona 85260
Toll-Free: 866.746.3015
Paris
26/36 rue Alfred Nobel 93600 Aulnay-sous-BoisToll-Free: 866.746.3015
Support: +33 1.58.31.10.65
Belfast
19 Colvin House Inspire Business Park Carrowreagh Road Belfast BT16 1QT, UK Toll-Free: 866.746.3015© 2016 Turning Technologies