Connecting the Video Projector
Tip: For optimal usage and viewing, the minimum required screen resolution should be set at 1024 x 768.
1 With the computer turned on, connect the projector video cable from the computer to the video projector. 2 Turn on the video projector. 3 With the video projector aimed at the DualBoard, align the projected image onto the DualBoard so that it is within the board’s active area.
TIP It is recommended to leave a 3 cm (30 mm) perimeter. Turning on the DualBoard 1 Connect the AC/DC power adapter to the DualBoard controller box. 2 Plug the opposite end of the AC/DC power adapter into a wall outlet. 3 Press the power switch on the right side of the board. A beep indicates that the board has power. Connecting the DualBoard via USB 1 Turn on your computer. 2 Connect the USB cable to the DualBoard controller box located on the back of the board. The controller box is located on the bottom right of the board, if the board has already been hung up. 3 Attach the other end of the USB cable into a working USB port on your computer. Device Manager establishes connection with the DualBoard.
Connecting the DualBoard Turning Technologies Device Manager version 7.3 or higher must be installed on your computer prior to installing the Wireless Kit. The RF receiver works best when it is not plugged into a computer that is under a podium or a desk. If necessary, use a USB extension cable to remove the RF receiver from under furniture that may shield the RF signal. 1 Connect the AC/DC power adapter to the DualBoard controller box. 2 Plug the opposite end of the AC/DC power adapter into a wall outlet. 3 Plug the end of the RJ12 cable into the DualBoard controller box located on the back of the board. The controller box is located on the bottom right of the board, if the board has already been hung up.
4 Slide the RF COM plastic grey holster over the board’s frame at the top of the DualBoard. 5 Seat the RF COM into the plastic grey holster. 6 Press the Power switch to the On position. 7 Plug the RF receiver into an available USB port on your computer. 8 Press the pairing button on the RF COM. The blue light will begin to blink. 9 Press the pairing button on the RF receiver.
IMPORTANT You have two minutes to press the pairing button. When the two devices have been successfully paired, the blue lights on the receivers will stop blinking and remain a solid blue. Pairing the device is a one-time operation. Regulatory Statements The following regulatory statements apply to radio frequency and infrared transmitters and receivers mentioned in this manual, including the ResponseCard RF, ResponseCard RF LCD, ResponseCard IR, ResponseCard XR, ResponseCard NXT and their respective receivers.
FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Declaration of Conformity Ohio 255 West Federal Street Youngstown, Ohio 44503 Toll-Free: 866.746.3015 International: +1.330.746.3015 Arizona 7400 East Tierra Buena Lane, Suite 103 Scottsdale, Arizona 85260 Toll-Free: 866.746.3015 Paris 26/36 rue Alfred Nobel 93600 Aulnay-sous-Bois Toll-Free: 866.746.3015 Support: +33 1.58.31.10.65 Belfast 19 Colvin House Dundonald Enterprise Park Carrowreagh Road Belfast BT16 1QT, UK Toll-Free: 866.746.3015
Tip: For optimal usage and viewing, the minimum required screen resolution should be set at 1024 x 768.
1 With the computer turned on, connect the projector video cable from the computer to the video projector. 2 Turn on the video projector. 3 With the video projector aimed at the DualBoard, align the projected image onto the DualBoard so that it is within the board’s active area.
TIP It is recommended to leave a 3 cm (30 mm) perimeter. Turning on the DualBoard 1 Connect the AC/DC power adapter to the DualBoard controller box. 2 Plug the opposite end of the AC/DC power adapter into a wall outlet. 3 Press the power switch on the right side of the board. A beep indicates that the board has power. Connecting the DualBoard via USB 1 Turn on your computer. 2 Connect the USB cable to the DualBoard controller box located on the back of the board. The controller box is located on the bottom right of the board, if the board has already been hung up. 3 Attach the other end of the USB cable into a working USB port on your computer. Device Manager establishes connection with the DualBoard.
Connecting the DualBoard Turning Technologies Device Manager version 7.3 or higher must be installed on your computer prior to installing the Wireless Kit. The RF receiver works best when it is not plugged into a computer that is under a podium or a desk. If necessary, use a USB extension cable to remove the RF receiver from under furniture that may shield the RF signal. 1 Connect the AC/DC power adapter to the DualBoard controller box. 2 Plug the opposite end of the AC/DC power adapter into a wall outlet. 3 Plug the end of the RJ12 cable into the DualBoard controller box located on the back of the board. The controller box is located on the bottom right of the board, if the board has already been hung up.
4 Slide the RF COM plastic grey holster over the board’s frame at the top of the DualBoard. 5 Seat the RF COM into the plastic grey holster. 6 Press the Power switch to the On position. 7 Plug the RF receiver into an available USB port on your computer. 8 Press the pairing button on the RF COM. The blue light will begin to blink. 9 Press the pairing button on the RF receiver.
IMPORTANT You have two minutes to press the pairing button. When the two devices have been successfully paired, the blue lights on the receivers will stop blinking and remain a solid blue. Pairing the device is a one-time operation. Regulatory Statements The following regulatory statements apply to radio frequency and infrared transmitters and receivers mentioned in this manual, including the ResponseCard RF, ResponseCard RF LCD, ResponseCard IR, ResponseCard XR, ResponseCard NXT and their respective receivers.
FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Declaration of Conformity Ohio 255 West Federal Street Youngstown, Ohio 44503 Toll-Free: 866.746.3015 International: +1.330.746.3015 Arizona 7400 East Tierra Buena Lane, Suite 103 Scottsdale, Arizona 85260 Toll-Free: 866.746.3015 Paris 26/36 rue Alfred Nobel 93600 Aulnay-sous-Bois Toll-Free: 866.746.3015 Support: +33 1.58.31.10.65 Belfast 19 Colvin House Dundonald Enterprise Park Carrowreagh Road Belfast BT16 1QT, UK Toll-Free: 866.746.3015